Spec

• Rating
• Function 1-step preset counter/2-step preset counter/total preset counter/batch counter/dual counter
• 2 preset levels
• Power supply voltage DC 12 ~ 24 V (ripple content less than 20%)
• Allowable Voltage Variation Range 85 ~ 110% of the supply voltage (90 ~ 110% for 12 ~ 24 VDC)
• Power consumption approx. 3.7 W
• Counter Counting Range - 999 ~ 9999
• Counter top counting speed 30 Hz/5 kHz (Minimum signal width: 16.7 ms (ON, OFF ratio 1: 1)/0.1 ms (ON, OFF ratio 1: 1))
• CP1, CP2 common settings
• Counter input mode Addition, subtraction, addition and subtraction (UP/DOWN A (command input), UP/DOWN B (individual input), UP/DOWN C (phase difference input))
• Counter Output Mode N/F/C/R/K -1/P/Q/A/K -2/D/L/H
• Counter One Shot Time 0.01 ~ 99.99 s Variable
• Counter return method External reset, manual reset, automatic reset (Such internal resets according to the operation of C, R, P and Q modes)
• Input signal CP1/CP2/Reset 1/Reset 2
• Input method Voltage free input/voltage input (switching)
• Nonvoltage input (noncontact input) Impedance at short circuit: 1 kohm
• Outflow current at 0 ohms: 12 mA
• Short circuit residual voltage: 3 V or less
• Open Impedance: 100 kohm
• Maximum applied voltage: 30 V
• Use contacts that can open and close 10 V 5 mA with no voltage input (contact input).
• Voltage input H level: 4.5 ~ 30 VDC
• L level: 0 ~ 2 VDC
• Input resistance: 4.7 kohm
• Applicable 2-wire sensor leakage current: 1.5 mA
• Opening and closing capacity: 5 mA
• Residual voltage: 3 V
• Power source ***d: Must operate at 10 VDC
• Minimum input signal width external reset: 1 ms/20 ms (switching)
• Standby time 290 ms
• Control Output (Contactless Output) Type: Transistor Output (NPN Open Collector)
• Opening/closing capacity: 30 VDC or less, 100 mA or less
• Residual voltage: 1.5 V or less (power: about 1 V)
• Leakage current: 0.1 mA
• Display method 7-segment negative LCD
• Digits 4
• Text height count/measurement: 12 mm (red/green/orange (switch))
• With zero suppression display
• Settings: 6 mm (green)
• Prescaling available (0.001 ~ 9.999)
• To the last three digits of the decimal point setting
• Key protect function Key protect switch
• No teaching function
• Has a batch count function
• No communication function
• Power outage memory EEP-ROM (Number of rewrites: 100,000 times or more Memory time: 10 years or more)
• When using ambient temperature range: -10 to + 55 degrees C
• When stored: -25 to + 70 degrees C
• However, for tight fitting: - 10 ~ 50 C (No condensation or freezing)
• When using ambient humidity range: 25 ~ 85% RH
• When stored: 25 ~ 85% RH
• Performance
• Insulation resistance 100 megohms or more (at 500 VDC megohms)
• Between conductive part terminal and exposed non-charged metal part/non-continuous contact
• Voltage: Between charged and uncharged metal parts: 2000 VAC, 50/60 Hz, 1 min
• Between the power and control input terminals: 1000 VAC, 50/60 Hz, 1 min.
• Between control output and power supply, input circuit: 1000 VAC, 50/60 Hz, 1 min
• Between discontinuous contacts: 1000 VAC, 50/60 Hz, 1 min
• Impulse voltage between power terminals: 1.0 kV
• Between conductive terminal and exposed uncharged metal part: 1.5 kV
• Between noise resistant power terminals: +/- 480 V
• Between input terminals: +/- 600 V
• Square wave noise (Pulse width 100 ns/1 micros, rising 1 ns) from a noise simulator
• Static electricity capacity 8 kV (malfunction), 15 kV (breakdown)
• Vibration resistance (***urance) 10 ~ 55 Hz, single amplitude 0.75 mm, 3 directions 2 h each
• Vibration resistance (malfunction) 10 ~ 55 Hz, single amplitude 0.35 mm in 3 directions 10 min each
• Impact resistance (***urance) 300 m/s * * 2 3 axes in 6 directions 3 times each
• Shock resistance (malfunction) 100 m/s * * 2 3 axes in 6 directions 3 times each
• Mechanical life 10 million times or more
• Electric life 100,000 times or more (AC 250 V 3 A resistance load)
• Protective structure front operating part: IEC standard IP 66, UL 508 Type 4 X (indoor) (when using rubber packing Y 92 S -29)
• Applicable Standard (UL) cUL (Listing): UL 508
• Applicable Standard (CSA) CSA C 22.2 No. 14
• Applicable Standard (VDE) VDE 0106/part 100
• Applicable Standard (EC Directive (Machine Directive) EN 61010 -1
• Applicable Standard (EC Directive (Low Voltage Directive) EN 61010 -1
• Applicable Standards (EC Directive (EMC Directive) EMI: EN 61326
• Radiation interference field strength: EN 55011 Group 1 Class A
• Noise Terminal Voltage: EN 55011 Group 1 Class A
• EMS: EN61326
• Electrostatic discharge immunity: EN 61000 -4 -2 (4 kV contact, 8 kV air)
• Field strength immunity: EN 61000 -4 -3 (10 V/m AM modulation (80 MHz to 1 GHz), 10 V/m pulse modulation (900 MHz +/- 5 MHz))
• Conductive noise immunity: EN 61000 -4 -6 (10 V (0.15 ~ 80 MHz))
• Burst noise immunity: EN 61000 -4 -4 (2 kV power line, 1 kV I/O signal line)
• Surge immunity: EN 61000 -4 -5 (Between 1kV lines (Power line, output line (relay output)), between 2kV ground (Power line, output line (relay output)))
• Voltage dip/cut immunity: EN 61000 -4 -11 (0.5 periods, 100% (rated voltage))
• Mounting method Embedded mounting
• External connection type screw tightening terminal
• Case Color Black (Mansell N 1.5) (The front panel can be changed to light gray or white, sold separately.)
• Accessories Embedded-Mounting Adapter/Waterproof Rubber Packing/Terminal Cover
• Mass (body): about 130 g