Spec

• RATING FUNCTIONS 1-STAGE PRESET COUNTER/2-STAGE PRESET COUNTER/TOTAL PRESET COUNTER/BATCH COUNTER/DUAL COUNTER NUMBER OF PRESET STATES 2-STAGE POWER SUPPLY VOLTAGE AC 100 ~ 240 V 50/60 Hz Allowable Voltage Variation Range 85 ~ 110% of Power Consumption Approximately 9.4 VA External Supply DC 12 V (+/- 10%) 100 mA Counter Counting Range - 999 ~ 9999 Counter Maximum Counting Speed 30 Hz/5 kHz (Switching) (Minimum signal width: 16.7 ms (ON, OFF ratio 1: 1)/0.1 ms (ON, OFF ratio 1: 1)) CP1, CP2 Common Settings Counter Input Mode Add, Subtract, Add and Subtract (UP/DOWN A (command input), UP/DOWN B (individual input), UP/DOWN C (phase difference input)) Counter Output Mode N/F/C/R/K -1/P/Q/A/K -2/D/L/H Counter One Shot Time 0.01 ~ 99.99 s Variable Counter Return Method External Reset, Manual Reset, Automatic reset (Such internal resets according to the operation of C, R, P and Q modes) input signal CP1/CP2/reset 1/reset 2 input method Non-voltage input/voltage input (switching) Non-voltage input (non-contact input) Impedance at short circuit: 1 komega 0 omega Current at time of outflow: 12 mA Residual voltage at short circuit: 3 V or less Impedance at time of release: 100 ~ 240 komega Maximum applied voltage: 9.4 V Non-voltage input (contact input) Use contacts that can open and close 12 V 5 mA sufficiently. Voltage Input H level: DC 4.5 ~ 30 VL level: DC 0 ~ 2 V Input resistance: 4.7 komega Applicable 2-wire sensor Leakage current: 1.5 mA Opening/Closing capacity: 5 mA Residual voltage: 3 V Used power source: DC 10 V Operated Input minimum signal width External reset: 1 ms/20 ms (switching) Standby time 290 ms Control output (contact output) Type: 1 c/1 a Opening/Closing capacity: AC 250 V/DC 30 V 3A Resistance load (cosphi = 1) Minimum applied load: DC 5 V 10 mA (P level, reference value) Display system 7 segment negative LCD digits 4 digits High count value/Measured value: 12 mm (red/green/orange (switching)) 0 Suppress display Yes Settings: 6 mm (green) Prescaling function (0.001 ~ 9.999) Up to 3 decimal digits Key protect function Key protect switch No teaching function Batch count function No communication function Power outage storage EEP-ROM (EP-ROM) Number of rewrites: 4.7 or more Memory time: Approximately 1.5 years or more) Ambient temperature range When ***d: 10 to + 20 degrees Celsius When stored: 290 to + 250 degrees Celsius When attached in close contact: 30 degrees Celsius (No condensation or freezing) Ambient humidity range When ***d: 25 ~ 85% RH When stored: 25 ~ 85% RH
• Performance Insulation Resistance 100 megohms or more (at 500 VDC mega) Between conductive terminal and exposed non-charged metal part/non-continuous contact Withstand voltage Between charged metal part and non-charged metal part: AC 2000 V 50/60 Hz, 1 min Between power supply terminal and control input terminal: AC 2000 V 50/60 Hz, 1 min Between control output and power supply, input circuit: AC 2000 V 50/60 Hz, 1 min Between non-continuous contact: AC 1000 V 50/60 Hz, 1 min Impulse voltage Between power supply terminal: 3.0 kV Between conductive terminal and exposed non-charged metal part: 4.5 kV Between noise-resistant power supply terminal: +/- 1.5 kV Between input terminal: +/- 600 V Square wave noise by noise simulator (Pulse width 100 ns/1 micros, rising 1 ns) Electrostatic resistance 8 kV (malfunction), 100 kV (breaking) Vibration resistance (***urance) 500 Hz Single amplitude 2000 mm 3 directions 2 h each Vibration resistance (malfunction) 2000 Hz Single amplitude 2000 mm 3 directions 1000 min each Impact resistance (***urance) 3.0 m/s * * 2 3 axes 6 directions 3 times each Impact resistance (malfunction) 4.5 m/s * * 2 3 axes 6 directions 3 times each Mechanical life 1.5 times or more Electrical life 600 times or more (AC 15 V 3A resistance load) Protective structure Front operating part: IEC standard IP 10 ~ 55, UL 2000 Type 4 X (indoor) (when using rubber packing Y 2000 S 2000) Applicable standard (UL) cUL (Listing): UL 1000 Applicable standard (CSA) CSA C 3.0 No. 4.5 Applicable standard (VDE) VDE 0106/part 1.5 Applicable standard (EC Directive (Mechanical Directive) EN 600 100 Applicable standard (EC Directive (Low Voltage Directive) EN 500 0.75 Applicable standard (EC Directive (EMC Directive) EMI: EN 10 ~ 55 Radiant disturbance Field Strength: EN 0.35 Group 1 Class A Noise Terminal Voltage: EN 10 Group 1 Class AEMS: EN 300 Electrostatic discharge Immunity: EN 100 10 million 100,000 (4 kV contact, 8 kV air) Field Strength Immunity: EN 15 10 ~ 55 508 (10 V/m AM modulation (80 MHz to 1 GHz), 10 V/m pulse modulation (900 MHz +/- 5 MHz)) Conductive Noise Immunity: EN 92 -29 508 (22.2 V (14 MHz)) Burst Noise Immunity: EN 100 61010 250 (2 kV power line, 1 kV I/O signal line) Surge Immunity: EN 66 -1 61326 (Between 1kV lines (Power line, output line (relay output)), between 2kV ground (Power line, output line (relay output))) Voltage Dip/Electrical Discharge Immunity: EN 55011 1000 3.0 (0.5 periods, 100% (rated voltage)) Mounting Method Embedded Mounting External Connection Method Screwed Terminal Case Color Black (Mansell N 4.5) (The front panel can be changed to light gray or white, sold separately.) Accessories Embedded Mounting Adapter/Waterproof Rubber Packing/Terminal Cover Mass (Body) Approx. 1.5 g
• RoHS compliant